An everyday lawn that looks the part. A 35 mm artificial grass for family gardens and landscaped outdoor spaces, offered in two material routes.
Need a sample or a quote? Find a supplier or installer
Products
ONE-DNA™ Elan 35
A fresh look for everyday living. A 35 mm artificial grass with a heavier yarn, for gardens, terraces, roof amenity spaces and landscaped outdoor areas.
Available in
100% PE
or100% PO
Description
A fuller lawn look for urban outdoor spaces
Terraces, roof gardens and small urban gardens are seen up close and used hard. A lawn there has to stand up well and look full from a short distance. ONE-DNA™ Elan 35 has the same 35 mm pile and stitch rate as Orion 35, with a heavier yarn, so it carries more fibre per square metre.
It is available in 100% PE and 100% PO. For the 100% PE route, a reaction-to-fire test report covers loose-laid installation without infill.
Products
Look at it up close
Fibre, tuft and backing. The same polymer family throughout the construction.
Top view, tuft and colour
Pile profile, 35 mm
Backing, PE or PP
Specifications and proof
Everything a specifier needs
Colors
Green
Gardens, terraces, roof amenity spaces, landscaped outdoor areas, events and interiors. In an early learning or play setting it is a landscape lawn, not a softfall surface.
Available as ONE-DNA™ 100% PE or ONE-DNA™ 100% PO, each with its own technical data. The values on this page are for 100% PE. Tell us how the lawn will be used and we'll advise which route suits it.
Built with FuseTech™, which bonds the fibres into the backing with heat instead of a latex or polyurethane secondary coating.
Tufted, with a heavier straight monofilament and a curled thatch. At the same pile height and stitch rate as Orion 35, the heavier yarn raises the face weight from 1,653 to 1,880 g/m² on the 100% PE route.
On the 100% PE route, the datasheet advises 10 kg of dried silica sand per square metre, grading 0.5 to 1.0 mm with about 80% rounded grains. For 100% PO, ask us for the infill advice.
650 l/min/m², the same for every ONE-DNA™ product.
ONE-DNA™ Elan 35 has no EN 1177 critical fall height result and is not intended for use under play equipment. On a roof, the roof designer specifies the build-up, drainage and fire requirements.
Reaction to fire depends on the installed build-up, because infill changes the result. For the 100% PE construction, a Ghent University test report covers loose-laid installation without infill; a sanded installation is a different configuration. The 100% PO construction has not yet been tested. Ask us for the documentation for your configuration.
Warranty and maintenance conditions are set out in our warranty terms.
Environmental data
Life cycle assessment
Life cycle assessment is part of how ONE-DNA™ products are developed and improved. Results are published once independently verified. Ask us about the status for this product.
Designed for recycling
It starts with the materials
Fibre and backing are joined without a latex or polyurethane coating, within one material route. Whether the product is recycled depends on collection and local processing.
Why this product
The close-up lawn
Where this product belongs.
Gardens
Terraces, roof gardens and urban gardens where the lawn is used hard and looked at from a short distance.
Where it fits
Applications
Each application page sets out what matters there and which ONE-DNA™ products fit.
Compare all nine productsTechnical documentation
The documents behind the product.
Need product specifications, installation guidance or supporting evidence? Tell us what you need and we'll help you find the relevant information for your project.
You may also consider
Other ONE-DNA™ products
Available in
100% PE
or100% PO
A fuller lawn. A little more luxury. A 40 mm artificial grass with more fibre weight than Orion 35, for gardens, roof terraces and landscape schemes.
Available in
100% PE
or100% PO
A little wilder. A lot more character. The longest pile in the range, at 45 mm, for larger gardens, landscape schemes and amenity lawns.
Related knowledge
ONE-DNA™ Elan 35 is used in gardens, terraces, roof amenity spaces, landscaped outdoor areas, events and interiors, where a full lawn is seen from close by.
On a roof or indoors the fire and drainage requirements of the project decide the build-up.
Both have a 35 mm pile and the same stitch rate. ONE-DNA™ Elan 35 uses a heavier 12,800/14 dtex yarn, so on the 100% PE route its face weight is 1,880 g/m² against 1,653 g/m² for Orion 35.
Elan 35 therefore carries more fibre per square metre. Colour and feel are best compared side by side as samples.
Elan 45 uses the same yarn at a longer 45 mm pile, with a face weight of 2,320 g/m² on the 100% PE route.
ONE-DNA™ Elan 35 gives a neater, shorter lawn; Elan 45 a deeper, more relaxed one for larger spaces.
For the 100% PE construction, loose laid without infill, Ghent University test report 24-0679-01 to EN ISO 9239-1 and EN ISO 11925-2 gives a result corresponding to Bfl-s1, tested to the European standard EN 13501-1. This is not an Australian fire class.
The result applies to that configuration only. A sanded installation and the 100% PO construction are not covered.
Not for current production. An earlier EPD to EN 15804+A2 (MRPI 1.1.00539.2024, modules A1 to A3) covers ONE-DNA™ Elan 35 in 100% PE made at Hasselt in the Netherlands. It does not cover production in Portugal or the 100% PO route. EPDs for current production are in their final stage.
Yes. ONE-DNA™ Elan 35 is offered in 100% PE and 100% PO, each with its own technical data. The values and fire test result on this page are for 100% PE.